REDRAGON M601WL-BA Wireless Gaming Mouse Instruction Manual – Manuals+

This page was created programmatically, to read the article in its original location you can go to the link bellow:
https://manuals.plus/redragon/m601wl-ba-wireless-gaming-mouse-manual
and if you want to remove this article from our site please contact us


REDRAGON M601WL-BA Wireless Gaming Mouse Instruction Manual
REDRAGON M601WL-BA Wireless Gaming Mouse

Dear user

Thank you for you choosing Logo Brand, to protect your rights and for better customer service, we ask that you note our warranty rules.

  1. Within guaranty period, repair is guaranteed for failure due to electrical circuit problems. Man-made damages, such as disassembly, hard impacts, submersion into water, plugging into improper current or voltage, and damage caused by natural disasters such as fire, flood, or earthquake are not included.
  2. Consumable parts (such as foot stick) and spare parts replacement are no included in our warranty.
  3. Please fill out the warranty card. Warranty card is valid with the stamp of the retailer.
  4. This warranty card will not be reissued if lost. Please keep it in a safe place.

OS support
Windows XPNista/Win7/Win8/Win10

Button Instructions

  1. Left mouse button (Defaulted as click, can’t be setting).
  2. Right mouse button (Defaulted as click).
  3. Scroll wheel button(Middle mouse button).
  4. Side button 1 (Defaulted to Forward).
  5. Side button 2 (Defaulted to Backward).
  6. DPI button (Switch among 800-1200-1600-2000-2400).
    Button Instructions

Right button + scroll wheel button ,press and hold both of buttons for 5 second to switch polling rate among 125Hz to 250Hz (default 125Hz).

Installation

  1. Plug Nano receiver to USB port on your computer.
  2. Install 1 AA battery in wireless mouse properly(Check the marker on battery storage before installation).
  3. Make sure the switch on bottom of mouse was set as ON mode.
  4. Press any key to get Mouse ready to work.

Wake up your wireless mouse
To save power, Mouse was program with a sleeping mouse when it is out of work for 8 minutes, Please press any key to wake up the mouse.

Reconnection

Both of mouse and Nano receiver has a built-in code, It can be setting one mouse to one receiver, or few of mouse to one receiver. Mouse and receiver need to reconnect under the condition of High temperature, high magnetic, strong vibrate.

  1. Plug off nano receiver from USB port, and plug it on.
  2. Keep the mouse in 50CM with receiver, re-store the battery, put the switch at “ON”, press any button to check the connection.
  3. Connection completely.

FAQ

  1. If the mouse is not responding, please check whether the mouse is plugged correctly in the corresponding computer USB port, or try another USB ports.
  2. If the mouse is moving slowly, jumping, or delaying, please try another surface. Surfaces that are dark, dirty, not flat, or bright may affect the performance of the mouse. Use of a mouse pad is strongly recommended.

FCC Statement

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1)this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Logo

Documents / Resources


This page was created programmatically, to read the article in its original location you can go to the link bellow:
https://manuals.plus/redragon/m601wl-ba-wireless-gaming-mouse-manual
and if you want to remove this article from our site please contact us

Leave a Reply

You have to agree to the comment policy.

7 − three =